# The Adequacy of NIOSH Equation to to Determine the Rate of Stresses Exerted on the Back Based on Compressive Force Estimation

AUTHORS

Davood Afshari 1 , Samira Kord 1 , * , Seyed Mahmood Latifi 2 , Ghasem Mardi 1

1 Department of Occupational Health, School of Public Health, Ahvaz Jundishapur University of Medical Sciences, Ahvaz, IR Iran

2 Department of Bio-Statistics, School of Public Health, Ahvaz Jundishapur University of Medical Sciences, Ahvaz, IR Iran

How to Cite: Afshari D, Kord S, Latifi S M, Mardi G. The Adequacy of NIOSH Equation to to Determine the Rate of Stresses Exerted on the Back Based on Compressive Force Estimation, Jundishapur J Health Sci. 2017 ; 9(1):e37726. doi: 10.17795/jjhs-37726.

ARTICLE INFORMATION

Jundishapur Journal of Health Sciences: 9 (1); e37726
Published Online: September 26, 2016
Article Type: Research Article
Revised: April 24, 2016
Accepted: May 21, 2016
Crossmark
CHECKING

### Abstract

Background: Manual handling may cause workers to deal with various risk factors. Workers performing such tasks repeatedly for a long time are more prone to bodily injuries and physical problems such as back pain.

Objectives: The current study aimed to assess the compressive loads estimation and analysis of forces exerted on the workers’ back in manual load lifting tasks using the national institute for occupational safety and health (NIOSH) equation and compare them with the recommended weight limit (RWL).

Methods: It was a cross-sectional study in a laboratory setting on 15 healthy male workers in 2015. The participants were required to randomly perform 25 tasks with four iterations. The lifting index (LI) was calculated by NIOSH equation in simple tasks and compressive loads on the low back (L4/L5) for each task were calculated using the 3DSSPP. Data were analyzed using SPSS version 16.

Results: The results showed that the highest compressive force exerted on the back was equal to 4002 N and the lowest force 1425 N. Moreover, 76% of the tasks were reported to have the highest compressive force greater than the recommended limit; 72% of the tasks had an LI 1 - 3 and 28% of them had an LI less than 1. There was a weak direct correlation between compressive force and RWL.

Conclusions: The NIOSH equation and compressive force estimation function were partially similar to identify high-risk tasks, however, by the compressive force estimation, biomechanical analysis of tasks can be done better since it is quantitative and can determine the exact amount of forces exerted on the back.

Keywords

### 1. Background

Manual material handling (MMH) may expose workers to deal with various risk factors. Workers performing such tasks repeatedly for a long time are more prone to bodily injuries and physical problems such as back pain. The main risk factors or conditions that cause injuries to progress in MMH tasks include poor postures (e.g. bending and twisting), repetitive movements (frequent access, lifting and carrying), applying high force (carrying or lifting heavy loads), pressure points (e.g. gripping loads, leaning on parts or hard surfaces with sharp edges) and static postures (e.g. maintaining a fixed position for a long time) (1). Back pain diseases are the most common musculoskeletal diseases; these diseases rank second in terms of physicians’ visits and rank fifth in terms of going to hospitals (2); therefore, the costs associated with them were approximately estimated as $72 billion in the United States in 1997, of which$171 million was related to the costs of back pain in industrial environments. Furthermore, half of all back injuries are caused by manually lifting the load (3-5). MMH is the main cause of damage to the workforce in the United States and four of every five occurred injuries are related to back pain caused by manual material handling (6). There are no official reports on the prevalence of work-related musculoskeletal diseases in Iran and the only official report was based on the reports by the treatment deputy of the social security organization (TDSSO) from 1992 to 1995, which announced musculoskeletal diseases as the cause of 14.4% of total disabilities in the country and also ranked musculoskeletal diseases fourth after the neurological diseases, psychiatric diseases and the cancer among all diseases. Moreover, according to the report by the same deputy in 2001, the highest number of visits to the medical commission for the social security organization (MCSSO) was due to musculoskeletal disorders (7). According to the report by national institute for occupational safety and health (NIOSH), about 60% of compensations arising from physical damages are related to the activity of manual load lifting (8). Statistical findings show that about 50% of back pains are related to lifting, 10% to pushing and pulling, and 6% to load carrying (9). Manual material handling tasks are widely performed in many professions (10). Several studies indicated a relationship between manual load carrying (without the use of auxiliary equipment) and an increased risk of musculoskeletal injuries, especially at the waist and upper extremity (11). Lifting load mechanical equipment such as lifts is effective to eliminate or reduce the injuries to the waist in cases that lifting loads exceed the load bearing capacity of the human. However, loads which humans are capable of handling manually should be moved manually since mechanical equipment carrying speed is much less than that of humans (12). In a study conducted by Arjmand et al. the revised NIOSH equation was used to estimate the forces applied on the vertebral column. For this purpose, 50 lifting tasks were simulated. The obtained results revealed that load lifting tasks in which the trunk forward bending angle is moderate to high (Over 30 degrees), vertebral column compressing forces greater than the recommended limit are created up to 40%. Moreover, the results indicated that it is necessary to consider a multiplier for the trunk forward bending angle (13). Rajaee et al. conducted a comparative study on six quantitative tools (HCBCF, LSBM, 3DSSPP, anybody, simple polynomial and regression) to estimate loads exerted on the spinal cord in 26 static activities. The results of this study showed that 3DSSPP software can be appropriate for symmetrical/asymmetrical tasks with low to moderate forward bending from the waist to perform tasks. In general, the results showed a major difference among tools to estimate the forces on the spinal cord especially compressive forces (14).

Previous studies determined safe limit values for tissues (15). The NIOSH proposed a back compressive force limit of 3,400 N in 1981, indicating that compressive loads less than 3400 N exerted on the back were placed in a safe area and in 1991, in a new edition of the load lifting instruction to reduce the risk of back pain, explained the recommended load amount; therefore, when a user handles a load heavier than the limit, the risk of back pain increases (16).

### 2. Objectives

Due to the high risk of back pain in manual material handling tasks, The current study aimed to assess the biomechanical estimation and analysis of forces exerted on the back in manual lifting tasks using the NIOSH equation and the University of Michigan’s 3D static strength prediction program (3DSSPP).

### 3. Methods

The current cross-sectional study was conducted from May to June 2015 at the ergonomics laboratory, Ahvaz University of Medical Sciences, Ahvaz, Iran. The participants of the study were randomly selected among male workers who were inexperienced in MMH tasks. The sample size was determined 15 based on the previous studies (17). The exclusion criteria were previous spinal surgery and a significant vertebral deformity resulting from any etiology. After meeting criteria, the study was explained and workers provided informed consent.

#### 3.1. The Study Design

Some boxes weighing 2, 5, 7, 9, 11, 14, 16, 18, 27 and 32 kg with suitable handles with the dimension of 60 × 38 × 31 cm were prepared. An identification code was then assigned to each of the boxes. The source for lifting the load was constant and the destination of the load was a shelf with four floors. The vertical heights of the floors of the shelf were as follows:

First floor: eight centimeters below the shoulder to 30 cm above the shoulder

Second floor: knuckle down to shoulder height

Third floor: leg height to knuckle height

Fourth floor: leg to floor height

Horizontal distances including close (30 cm), medium (60 cm) and spread (80 cm) were marked at the destination toward the middle ankle.

The participants were required to randomly perform 25 tasks with four iterations. An identification code was also assigned to each task.

It should be noted that load weights and the horizontal and vertical distances were determined based on threshold limit values (TLVs) tables provided by the Ministry of Health and Medical Education of Iran. According to the previous study, the boxes with such dimensions are commonly used in the range of jobs available in the community. Moreover, the boxes at Iran’s domestic market have the closest dimensions to the ones used in previous studies (17).

#### 3.2. Instrumentation and Method

In the present study to estimate the compressive force, the forward bending angle at the waist was firstly measured online with direct observation using a portable three-axis inclinometer (WILLISTON VT, Inc., USA, MicroStrain. VC-223) made in the United States. The device is fastened around the chest above the sternum and 2.5 cm below the collarbone in a belt containing a small bag. Prior to implementing the device, it was calibrated according to the manufacturer's instruction. The accuracy of the device is reported ± 0.5 degree in various studies, according to the manufacturer statement (18, 19).

To record the trunk reference angle and make each participant’s natural trunk angle equal to zero, after placing the device inside the bag, the participants were asked to stand in an upright posture for 30 seconds; therefore, the upper body was fully stretched and upright.

To ensure that no change occurred to the position of the device inside the bag and or to the position of the bag on the body, each participant was again asked after the sampling to stand in a stretched and upright posture for thirty seconds and the final reference angle was also recorded. Then, the compressive force exerted on the back was determined using 3DSSPP.

At the beginning of the task, a lumbar inclinometer was attached to each individual and the participants were randomly asked to perform the tasks and their iterations. The individuals were given 30 seconds to rest after each task. In order to minimize the influence of fatigue caused by load lifting on next tasks, each individual was given a five-minute break after five minutes of activity (performing five tasks). Moreover, no information was disclosed to the individuals regarding weights of loads and forces they exerted when lifting.

Since the information needed to determine the coefficients of load lifting was specific, the recommended weight limit (RWL) was calculated in simple conditions by the NIOSH lifting equation.

#### 3.3. Statistical Analysis Methods of the Results

The greatest exerted compressive force by each individual was accounted for four iterations of each task. Eventually, the data were transferred into the SPSS version 16 (SPSS Inc., Chicago, IL, USA). The Kolmogorov-Smirnov test was used to examine the normality of the distribution of data. Pearson correlation test was used to determine the relationship between RWL and the compressive force due to the parametric nature of the data. Moreover, the regression test was used to determine the correlation between the mean compressive forces and lifting index (LI).

Since the data distribution was normal, the T-test was used to compare the compressive forces exerted on the back at the recommended limits.

### 4. Results

Table 1 shows the demographic characteristics of the participants. The mean age of the participants was 30.13 ± 6.14 years. The mean compressive force exerted on the back at various horizontal and vertical distances from the body are shown in Table 2. Of the 25 performed tasks, the greatest compressive force exerted on the back was related to task 3 equal to 4002 N and the lowest one was related to task 11 equal to 1425 N. According to the greatest compressive forces, it was observed that 19 tasks (76%) had the maximum compressive force higher than the recommended limit (3400 N).

Table 1. Demographic Characteristics of the Study Population
VariableMean ± SDMinimumMaximum
Age, y30.13 ± 6.142341
Work experience, y10.75 ± 4.23418
Height, cm172.27 ± 9.24141179
Weight, kg74 ± 10.536193
Table 2. Estimate Compressive Forces on the Back, the Recommended Weight Limit and Lifting Index
LIRWLMean ± SDMaxMinCompare With Standard
116175301.481082245 ± 81943691585Sa
27175601.29541735 ± 59233191221S
33295302.131494002 ± 74260033231(P = 0.003)b,c
41695602.13743373 ± 51643182487S
5995801.6562915 ± 31934132277S
61870301.071663292 ± 101649931866S
71470601.67832750 ± 109645001669S
8770801.11622138 ± 98337301263S
91420300.81732702 ± 125645101623S
1014175301.44962125 ± 64035821264S
115175601.033481425 ± 4752738980S
122795302.011343561 ± 62150572606(P = 0.16)b
131495602.08673103 ± 42641092597S
14795801.39502667 ± 28231802095S
151670301.071492984 ± 102948511936S
161170601.47742485 ± 104441281529S
17570800.89551963 ± 90633671101S
18920300.571552287 ± 113242141281S
1911175301.13961721 ± 53132881207S
201495301.041342693 ± 38335552054S
21995601.34672670 ± 31633052327S
22595800.99502486 ± 50534611685S
23970300.61492563 ± 88738721403S
24770600.93742144 ± 95537071240S
25270800.35551761 ± 10084044916S

aMeans that the mean compressive force is significantly less than the recommended standard.

bMeans that the mean compressive force is significantly higher than the recommended standard.

cThe load constant was equal to 23 kg. In addition, the asymmetry multiplier (AM) and the coupling multiplier (CM) were both taken as 1.

As shown 18 tasks out of 25 (72%) had the lifting index between one and three, and seven tasks (28%) had an LI less than one.

The results obtained from the statistical tests showed that existence of a direct weak correlation between the compressive force obtained from the University of Michigan’s program and that of the RWL (correlation coefficient = 0.47, P value = 0.01). Moreover, the results indicated a significant correlation between the compressive force and the lifting index (r = 0.63, P value = 0.001).

### 5. Discussion

As it can be observed, the mean compressive force in tasks 3 and 12 were higher than those of the standard recommended limit (3400 N). It can be due to the heavier weights of these tasks. Asadi et al. who used the 3DSSPP program to estimate compressive forces exerted on the workers’ backs during manual load lifting, concluded that the compressive forces in 17.5% of the subjects were beyond the permissible limit (20). However, the results of the study showed that the mean compressive force was higher than the permissible limit in only 8% of the tasks.

The highest compressive force values exerted on the back in the study showed that 19 out of 25 performed tasks (76%) had a compressive force higher than the recommended limit (3400 N). Faber et al. conducted a study on 12 healthy males in Amsterdam, where the participants lifted 10 and 20 kg loads from a height of 29 cm in front of their bodies. They estimated the compressive forces exerted on the participants’ backs using kinematic and electromyographic measurements. The maximum compressive forces exerted on the back in these two tasks were 4898 and 5480 N, respectively, which were greater than the recommended limit (26). By comparing the results of the current study with those of Faber, it seems that performing similar tasks can create compressive forces higher than the recommended limits in some individuals, while creating compressive forces below the permissible limit in some others.

Russell et al. compared the results of five load lifting analysis tools, including NIOSH, ACGIH TLV, SNOOK, 3DSSPP, and WA L&I, and stated that it was easier to use the ACGIH TLV, SNOOK and WA L&I methods; however, the NIOSH method had a broader range to determine that a change in which aspect of the load lifting operation can have a greater impact in reducing the force exerted on the back (27). The results obtained by the inclinometer and the NIOSH equation were compared as follows.

The compressive force was higher than the permissible limit in tasks 3 and 12, indicating them as high-risk tasks. However, according to the results obtained from the NIOSH equation, LI was greater than one, which indicated intermediate risk of such tasks. Moreover, tasks 4, 6, 7, 13, 15 and 16, which had high risk of back injury by considering one standard deviation above the mean compressive force, were considered to have moderate risk by the NIOSH equation. Morshedi et al. observed that the compressive force in the performed tasks was greater than that of the standard recommenced limit and the tasks were determined as high-risk ones, while the results obtained by the NIOSH equation indicated the moderate risk of the tasks (22).

Tasks 9, 18 and 23 which exceeded the standard recommended limit by considering one standard deviation above the mean compressive force, were identified as low risk by the NIOSH equation.

Tasks 1, 2, 5, 8, 10, 11, 14, 19, 20 and 21 had a mean compressive force less than that of the standard recommended limit. However, they were identified as the moderate risk tasks by the NIOSH equation. The study by Russell et al. showed that based on the NIOSH load lifting equation, the intended task had a high risk of musculoskeletal disorders occurrence, while estimating the compressive force using the University of Michigan’s software identified the same task as low-risk (27).

The results of the comparison between the two methods indicated a significant correlation between the compressive force obtained from the University of Michigan's software and that of the lifting index (r = 0.63, P value = 0.001). In the study by Russell et al. a significant difference was observed between the results obtained from the NIOSH load lifting equation and those of the University of Michigan’s software that contradicted with the results of the current study (27).

#### 5.1. Conclusions

Based on the correlation obtained between the results of the NIOSH load lifting equation and that of the compression load, it can be concluded that the two mentioned methods had partially similar functions to identify high-risk tasks, however, using the compressive force estimation, biomechanical analysis of tasks can be done better, since it is quantitative and can determine the exact amount of forces exerted on the back.

In the current study, the moment compression force was considered as the evaluating criterion and cumulative compressive force calculations were not carried out; since the number of high risk tasks may increase by calculating the cumulative compressive force for the performed tasks, the cumulative compressive force should be considered for evaluation in future studies.

#### 5.2. Limitation

Due to the large number of assessed tasks and the time-consuming process of review, the sample size was determined 15 participants and more participants can be included in further investigations.

### References

• 1.

Rossi D, Bertoloni E, Fenaroli M, Marciano F, Alberti M. A multi-criteria ergonomic and performance methodology for evaluating alternatives in “manuable” material handling. Int J Industr Ergon. 2013; 43(4) : 314 -27

• 2.

Nozad HAM. Investigate factors affecting occupational low back pain in workers of some factories in Ardbil and offering preventive strategies. J Ardabil Univ Med Sci. 2002; 1(2) : 27 -33

• 3.

Boston JR, Rudy TE, Mercer SR, Kubinski JA. A measure of body movement coordination during repetitive dynamic lifting. IEEE Transact Rehabil Engin. 1993; 1(3) : 137 -44

• 4.

Buseck M, Schipplein OD, Andersson GB, Andriacchi TP. Influence of dynamic factors and external loads on the moment at the lumbar spine in lifting. Spine (Phila Pa 1976). 1988; 13(8) : 918 -21 [PubMed]

• 5.

De Luca CJ. The use of surface electromyography in biomechanics. J Appl Biomechan. 1997; 13 : 135 -63

• 6.

Occupational Safety &amp; Health Administration(OSHA). 2011;

• 7.

Mehrparvar AH, Ranjbar S, Mostaghasi M, Salehi M. Evaluating the risk of musculoskeletal disorders by QEC in a food factory. Occup Med Q J. 2011; 3(2) : 54 -60

• 8.

Sadeghi N, Fani MJ, Aboutorabi H. Compare the weight of the load carried by the Industrial Workers of the amount recommended by the NIOSH. 7th International Industrial Engineering Conference;. 2010;

• 9.

Motamedzadeh M, Dormohamadi A, Sardroodi H, Zarei E, Darmohamadi R, Sahafei Motlagh M. The ergonomic design and application of the NIOSH equation on immunization of lifting tasks. J Arak Univ Med Sci. 2013; 16(6) : 90 -100

• 10.

Faber GS, Kingma I, van Dieen JH. Effect of initial horizontal object position on peak L5/S1 moments in manual lifting is dependent on task type and familiarity with alternative lifting strategies. Ergonomics. 2011; 54(1) : 72 -81 [DOI][PubMed]

• 11.

Nussbaum MA, Chaffin DB, Stump BS, Baker G, Foulke J. Motion times, hand forces, and trunk kinematics when using material handling manipulators in short-distance transfers of moderate mass objects. Appl Ergon. 2000; 31(3) : 227 -37 [PubMed]

• 12.

Heydari H, Hoviat Talab M, Azeghani MR, Ramezan Zadeh M, Parnian Pour M. The effect of wearable supportive devices in the reduction of forces in the erector spinae muscles in keeping tasks using biomechanical modeling and EMG sampling. Res Rehabil Sci. 2011; 7(2) : 169 -78

• 13.

Arjmand N, Amini M, Shirazi-Adl A, Plamondon A, Parnianpour M. Revised NIOSH lifting equation may generate spine loads exceeding recommended limits. Int J Industr Ergon. 2015; 47 : 1 -8

• 14.

Rajaee MA, Arjmand N, Shirazi-Adl A, Plamondon A, Schmidt H. Comparative evaluation of six quantitative lifting tools to estimate spine loads during static activities. Appl Ergon. 2015; 48 : 22 -32 [DOI][PubMed]

• 15.

Potvin JR, Chiang J, Mckean C, Stephens A. A psychophysical study to determine acceptable limits for repetitive hand impact severity during automotive trim installation. Int J Industr Ergon. 2000; 26(6) : 625 -37

• 16.

Konz S. NIOSH lifting guidelines. Am Ind Hyg Assoc J. 1982; 43(12) : 931 -3 [DOI][PubMed]

• 17.

Wu SP. Maximum acceptable weight of lift by Chinese experienced male manual handlers. Appl Ergon. 1997; 28(4) : 237 -44 [PubMed]

• 18.

Amasay T, Zodrow K, Kincl L, Hess J, Karduna A. Validation of tri-axial accelerometer for the calculation of elevation angles. Int J Industr Ergon. 2009; 39(5) : 783 -9

• 19.

Van Driel R. Evaluating methods to use the Virtual Corset™ inclinometer for trunk posture measurements. 2009;

• 20.

Asadi N, Choobineh AR, Keshavarzi S, Daneshmandi H. Estimate of low back loads in manual lifting tasks using 3DSSPP. J Ergon Human Factors Engin Iran. 2014; 2(4) : 25 -31

• 21.

Habibi EA, Kazemi M, Safari S, Hassanzadeh A. Relationship between the material handdling capacity by NIOSH method and the risk of musculoskeletal disorders by Rapid upper limb assessment (RULA) on the Welfare Organization staffs of Isfahan. J Res Health System. 2012; 8(1) : 131 -7

• 22.

Morshedi R, Boazar M, Afshari D. Biomechanical analysis of manual lifting of loads and ergonomics solutions for nursing assistants. J Ergon. 2015; 3(1) : 17 -24

• 23.

Wu SP. Maximum acceptable weights for asymmetric lifting of Chinese females. Appl Ergon. 2003; 34(3) : 215 -24 [DOI][PubMed]

• 24.

Callaghan J, Jackson J, Albert W, Andrews D, Potvin J. The design and preliminary validation of '3D-Match'-a posture matching tool for estimating three dimensional cumulative loading on the low back. 24th Association of Canadian Ergonomists (ACE) Conference. 2003;

• 25.

Hoozemans M, Kingma I, de Vries W, van Dieen J. Effect of lifting height on low back loading. International Ergonomics Association Conference. 2006;

• 26.

Faber GS, Kingma I, Bakker AJ, van Dieen JH. Low-back loading in lifting two loads beside the body compared to lifting one load in front of the body. J Biomech. 2009; 42(1) : 35 -41 [DOI][PubMed]

• 27.

Russell SJ, Winnemuller L, Camp JE, Johnson PW. Comparing the results of five lifting analysis tools. Appl Ergon. 2007; 38(1) : 91 -7 [DOI][PubMed]

• Copyright © 2016, Ahvaz Jundishapur University of Medical Sciences. This is an open-access article distributed under the terms of the Creative Commons Attribution-NonCommercial 4.0 International License (http://creativecommons.org/licenses/by-nc/4.0/) which permits copy and redistribute the material just in noncommercial usages, provided the original work is properly cited.